Riesel base 3 reservations/statuses/primes

[KEP]

Originally Posted by rogue

I assume you mean that these ranges are released and not other ranges for which you have a reservation. Is that correct?

Yes, only 18G-20G, 27G-33G and 8G-13G reservations is released, since they are complete.

My remaining R3 reservation for 33G-43G to n=25K is in progress and still reserved.

[rebirther]

R3 tested to n=200k (150-200k) (5-6G)

241 primes found, 926 remain in this range

Results emailed, Base released

[rebirther]

Reserving R3 from n=160-225k (1-2.147G) for BOINC

[rogue]

I'm going to try this out for R3. I'll take 60000000001 thru 63064644938. If I've been following correctly that will leave 43G thru 60G as unassigned. This will be done on a 4-core Xeon that does not have AVX, so I'm not certain how long this will take. Based upon other results, there should be between 18,000 and 20,000 k remaining when I'm done.

[VBCurtis]

Posts 688-689, I reserved 62G-up. I did complete 63G-up, and did 62.0 to 62.2 to 25k. However, the number of k's remaining for the two runs do not correlate well, so I got worried I did something wrong. I never got around to troubleshooting (or repeating my 63G-up run as a doublecheck), so go ahead with your plan.

If you could report your number of k's remaining from 62.0 to 62.2, I will do the same so I have a sanity check on my run.

I think I ran 63.0-up to 100k; I'll post the primes found above 25k when I am next on that machine.

[rogue]

Originally Posted by VBCurtis

Posts 688-689, I reserved 62G-up. I did complete 63G-up, and did 62.0 to 62.2 to 25k. However, the number of k's remaining for the two runs do not correlate well, so I got worried I did something wrong. I never got around to troubleshooting (or repeating my 63G-up run as a doublecheck), so go ahead with your plan.

If you could report your number of k's remaining from 62.0 to 62.2, I will do the same so I have a sanity check on my run.

I think I ran 63.0-up to 100k; I'll post the primes found above 25k when I am next on that machine.

I didn't check the reservation page and I did not look back far enough on this thread. I'll do from 60G to 63G then. I'll assume that your results for > 63G are good.

[gd_barnes]

Originally Posted by rogue

I didn't check the reservation page and I did not look back far enough on this thread. I'll do from 60G to 63G then. I'll assume that your results for > 63G are good.

OK I reduced Mike's reservation to k>63G and I have added Mark's reservation for k=60G-63G.

Mike, please report your primes and k's remaining for k>63G.

Mark, please do not stop and restart your srbase program at any point when running R3. If it stops unexpectedtly, please start over. Best would be to run medium-sized k ranges. We had a lot of problems on your R940 reservation when that happened. We need extreme accuracy on R3.

[rogue]

Originally Posted by gd_barnes

Mark, please do not stop and restart your srbase program at any point when running R3. If it stops unexpectedtly, please start over. Best would be to run medium-sized k ranges. We had a lot of problems on your R940 reservation when that happened. We need extreme accuracy on R3.

Agreed. The problem with R940 was an unplanned power outage. That happens very rarely around here. I will be gone much of December, so hopefully that won't happen while I'm gone.

[rebirther]

R3 tested to n=225k (160-225k) (1-2.147G)

287 primes found, 951 remain in this range

Results emailed, Base released

[rebirther]

Reserving R3 from n=200-250k (5-6G) for BOINC

[rebirther]

R3 tested to n=250k (150-250k) (5-6G)

382 primes found, 785 remain in this range

Results emailed, Base released