How to proceed (sieve, LLR, P1) depends on which method removes candidates faster. For sieving that's a bit hard to determine since it removes an n=10M almost as fast as n=1M while the LLR of the former takes 100 times more.
For P1 vs LLR it's easy though. Just time how long LLR takes to remove 10 candidates and how long P1 would take in the same range. I strongly suspect P1 doesn't make sense. It's only useful for Mersennes because they are so large and have those specially formed factors including the exponent. Here's how I do it: do a few LLR tests and write down the average time. Then sieve for 12 days and see if that removes candidates faster or not. If yes, continue sieving, if not, continue LLR until an LLR test again takes longer to remove a candídate than sieving did. 
[QUOTE=bur;594351]How to proceed (sieve, LLR, P1) depends on which method removes candidates faster. For sieving that's a bit hard to determine since it removes an n=10M almost as fast as n=1M while the LLR of the former takes 100 times more.
For P1 vs LLR it's easy though. Just time how long LLR takes to remove 10 candidates and how long P1 would take in the same range. I strongly suspect P1 doesn't make sense. It's only useful for Mersennes because they are so large and have those specially formed factors including the exponent. Here's how I do it: do a few LLR tests and write down the average time. Then sieve for 12 days and see if that removes candidates faster or not. If yes, continue sieving, if not, continue LLR until an LLR test again takes longer to remove a candídate than sieving did.[/QUOTE]:smile::yucky::yucky: Thank you for your insights 1. I have retested the primes found by gd_barnes : they are confirmed 2. On my i3 I am sieving the input from gd_barnes to 260T: eta 03/22 3. On my i5 imac I am llr’ing the range 1.3m to 1.4m each candidate takes 733 seconds 4. Sieving on that latest machine I am eliminating a candidate each 500  550 seconds 4.1. On a sidenote gd_barnes Saïd to me you are missing factors due to a wrong setting in NewPgen, my file ranges from 1.3m to 50m and I already sieved to 260T … taking this up from the beginning will take also take time 5. I will take a stab at p1 when my current range is done or will try it on my i7 portable (laptop) Ftm I am recovering from a mild Covid infection :yucky: Kind regards, Valerie 
If you're going to LLR test the entire file, then one should sieve until the factorremoval rate is half as fast (twice the seconds per factor) as an LLR test takes for the smallest candidate in the file.
This is due to the way the sieve scales when you take candidates out of the sieve for LLR, the sieve speed does not change linearly. Since there is not much speed to be gained by taking candidates out, we leave the small candidates in longer than commonsense might suggest. A rough scaling example: If you take out 10% of the candidates from the sieve file, the sieve only runs ~5% faster ("faster" as measured by p/sec). 
I gathered a few statistics:
 Sieving yields a factor each 552 seconds  An llr test takes 735 seconds for the range 1.3M > 1.4M (which I am currently busy testing)  A P1 test takes 30 minutes, with bounds B1 = 1M  An ECM test takes 30 minutes for each curve, with bounds B1 = 1M For the moment, I will complete the range 1.3M > 1.4M Kind regards, Valerie 
P1 is useless for Riesel candidates for the reasons bur listed. In fact, your tested B1 of 1M is higher than what GIMPS recommends even for wavefront (i.e. [I]p[/I]~105M) Mersenne candidates (which is in the 800k range on my computer). Bounds that high are only used on numbers in the 1.3Mbit range when we're trying to (partially) [I]factor[/I] it, not pretest before running a primality test.

1 Attachment(s)
Range 1.3M > 1.4M completed, no new primes to report.
All ranges resieved up unto 260T & LLR'ed to 1.3M, the outputs are matching my results Will sieve until 300T Kind regards, Valerie 
With the energy prices surging in Europe, I have decided to halt my efforts on this project.
I have sieved the number to 270T en tested it to 1.4M. Please find attached the link to my Google Drive where you can pickup this file. If this does not work please PM your (Project responsible) with your mail address and I will then transfer the input to you. It was a fun, and certainly a long and a happy time. I hope I will back, when the prices are stabilizing. [url]https://drive.google.com/file/d/1LMpLUiw6xVnYRS2zNgsZAzhzo4P3AQp6/view?usp=sharing[/url] Kind regards Valerie 
All times are UTC. The time now is 16:58. 
Powered by vBulletin® Version 3.8.11
Copyright ©2000  2022, Jelsoft Enterprises Ltd.